My cs3 dont find my New m84 Share  Email this topic  LinkBack Topic URL  Retweet this Topic  Share Topic on Google+  Like this Topic  Share on Facebook  Digg this Topic  Reddit this Topic  Share on Tumblr Options  Watch this topic  Print this topic View » Normal Threaded

Previous Topic Next Topic

Mille		#1 Posted : 10 May 2023 10:03:36(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		Light is on and i have tried Another adres but cs3 says no New mfx articles can be found Anyone know why or have an idea why??
User Profile View All Posts by User View Thanks

	Wish to join the discussion?! Login to your marklin-users.net community | Forum accountor Register a new forum account. Or Connect via Facebook

clapcott		#2 Posted : 10 May 2023 10:27:47(UTC) Retweet
Joined: 12/12/2005(UTC) Posts: 2,433 Location: Wellington, New_Zealand		Please specify which m84 ( m84.1 = 60841=white, m84.2 = 60842 = black) only the m84.2 is mFX configuration ready what do you mean by "light is on" - which light. refer manual for correct led status indications (next to red/brown feed) please confirm the CS3 mFX protocol has not been disabled.
		Peter
User Profile View All Posts by User View Thanks

Mille		#3 Posted : 10 May 2023 11:40:15(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		The black m84 I mean the led light is on so it got power
1 user liked this useful post by Mille		marklinist5999
User Profile View All Posts by User View Thanks

marklinist5999		#4 Posted : 10 May 2023 14:20:43(UTC) Retweet
Joined: 10/02/2021(UTC) Posts: 3,117 Location: Michigan, Troy		What is the dip switch set for? DCC, MM, or MFX
User Profile View All Posts by User View Thanks

Mille		#5 Posted : 10 May 2023 14:59:38(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		2,3,4 Should be adres 53-56 in manual
User Profile View All Posts by User View Thanks

Goofy		#6 Posted : 10 May 2023 15:40:31(UTC) Retweet
Joined: 12/08/2006(UTC) Posts: 9,012		Originally Posted by: Mille 2,3,4 Should be adres 53-56 in manual Dip switch number 10 are to set MM or DCC. I recommended you try DCC protocol and click to search mfx article. Good luck!
		H0 DCC = Digital Command Control
1 user liked this useful post by Goofy		marklinist5999
User Profile View All Posts by User View Thanks

Mille		#7 Posted : 11 May 2023 05:23:09(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		Still no luck Dont know what more i can try
1 user liked this useful post by Mille		marklinist5999
User Profile View All Posts by User View Thanks

marklinist5999		#8 Posted : 11 May 2023 14:22:31(UTC) Retweet
Joined: 10/02/2021(UTC) Posts: 3,117 Location: Michigan, Troy		If you've already disconnected it and retried, maybe it's defective? Have you checked all. The CS3 settings for correct parameters?
User Profile View All Posts by User View Thanks

Mille		#9 Posted : 12 May 2023 05:24:05(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		What should be correct settings in cs3 then?
User Profile View All Posts by User View Thanks

LSQ		#10 Posted : 12 May 2023 08:06:50(UTC) Retweet
Joined: 22/06/2019(UTC) Posts: 22 Location: TIANJIN		1. Try another set of address; 2. If have other workable 60842 in CS3, may replace it by new 60842 with same address to see what will happen.
1 user liked this useful post by LSQ		marklinist5999
User Profile View All Posts by User View Thanks

marklinist5999		#11 Posted : 12 May 2023 16:01:33(UTC) Retweet
Joined: 10/02/2021(UTC) Posts: 3,117 Location: Michigan, Troy		Yes, and set to DCC, there are more addresses possible, no? Or is it MM? I think the German "trainguy" on YouTube shows how.
User Profile View All Posts by User View Thanks

Goofy		#12 Posted : 13 May 2023 10:26:30(UTC) Retweet
Joined: 12/08/2006(UTC) Posts: 9,012		Test by reset CS3. It is possible that CS3 needs to be clean up. I did have same similar problem with m83. After reset CS3 the m83 did start work again.
		H0 DCC = Digital Command Control
1 user liked this useful post by Goofy		marklinist5999
User Profile View All Posts by User View Thanks

FrankF		#13 Posted : 16 May 2023 00:50:44(UTC) Retweet
Joined: 18/11/2007(UTC) Posts: 106		There has been a range of Marklin 60842 - M84 Decoders which is not working "correct" because of a failure made under Production. These cant be programmed "manually" or with "mfx" and is not working correct. If the M84 Decoder's Label on the backside of the M84 Decoder has a Serial-number where the last 5 Digits in the Serial-number is inside the Serial-number range shown in the following listing : 41682-41861 40869-41501 40462-40783 38711-40423 37228-38126 then the M84 Decoder has a Production-failure and can be replaced by your Dealer. Contact your local Marklin Dealer for more Information.
		CS3+ 60216 ( SW:2.5.2 ) - MASTER / CS2 60215 ( SW:4.3.0 ) - SLAVE MS2 60653/57 ( SW:4.13 ) / MS1 60652 ( SW:1.8AP ) / 60883 S88 LINK ( SW:1.1 ) MDT 3 (SW 3.6.0) - HW: 60970 / 60971 / 60801 ESU LOKPROGRAMMER ( SW 5.2.6 ) / ESU HW: 53451 / 53900 / 53901
		WWW
1 user liked this useful post by FrankF		marklinist5999
User Profile View All Posts by User View Thanks

Mille		#14 Posted : 16 May 2023 07:29:30(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		Sadly my m84 number was not there I managed to get it work once but i needed to delete m84 from article list becuse i choosed an occupied adres After that cs3 dont find it again even if i have tried many different dipswitch settings Anyone have an idea why??
1 user liked this useful post by Mille		marklinist5999
User Profile View All Posts by User View Thanks

FrankF		#15 Posted : 16 May 2023 09:48:05(UTC) Retweet
Joined: 18/11/2007(UTC) Posts: 106		Connect the M84 Decoder to the Programming-track and try to read out the M84 - CV Parameters under DCC. If you can do that set CV 8 to the value "8" and try to reset the M84 Decoder under DCC and see if this helps you with your problems. The M84 Decoder only uses MFX-Protokol to add the M84 Decoder to the Article-List , after that the M84 Decoder is used with the MM or DCC Protokol to control the Switching Articles.
		CS3+ 60216 ( SW:2.5.2 ) - MASTER / CS2 60215 ( SW:4.3.0 ) - SLAVE MS2 60653/57 ( SW:4.13 ) / MS1 60652 ( SW:1.8AP ) / 60883 S88 LINK ( SW:1.1 ) MDT 3 (SW 3.6.0) - HW: 60970 / 60971 / 60801 ESU LOKPROGRAMMER ( SW 5.2.6 ) / ESU HW: 53451 / 53900 / 53901
		WWW
1 user liked this useful post by FrankF		marklinist5999
User Profile View All Posts by User View Thanks

Mille		#16 Posted : 16 May 2023 12:38:09(UTC) Retweet
Joined: 02/02/2023(UTC) Posts: 64 Location: Stockholm		Tried it but only things that happen is that it add a new article called X1 with adres 12 Guess i need go to my Märklin dealer Thanks for all help
1 user liked this useful post by Mille		marklinist5999
User Profile View All Posts by User View Thanks

Goofy		#17 Posted : 18 May 2023 12:11:23(UTC) Retweet
Joined: 12/08/2006(UTC) Posts: 9,012		Originally Posted by: FrankF There has been a range of Marklin 60842 - M84 Decoders which is not working "correct" because of a failure made under Production. These cant be programmed "manually" or with "mfx" and is not working correct. If the M84 Decoder's Label on the backside of the M84 Decoder has a Serial-number where the last 5 Digits in the Serial-number is inside the Serial-number range shown in the following listing : 41682-41861 40869-41501 40462-40783 38711-40423 37228-38126 then the M84 Decoder has a Production-failure and can be replaced by your Dealer. Contact your local Marklin Dealer for more Information. Strange...i have never notice information by Märklin about the digital problems. It should be present but never heard about info by Märklin.
		H0 DCC = Digital Command Control
User Profile View All Posts by User View Thanks

Users browsing this topic