 Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
Light is on and i have tried
Another adres but cs3 says no
New mfx articles can be found
Anyone know why or have an idea why??
|
|
|
|
|
|
 Joined: 12/12/2005(UTC) Posts: 2,448 Location: Wellington, New_Zealand
|
Please specify which m84 ( m84.1 = 60841=white, m84.2 = 60842 = black)
only the m84.2 is mFX configuration ready
what do you mean by "light is on" - which light.
refer manual for correct led status indications (next to red/brown feed)
please confirm the CS3 mFX protocol has not been disabled.
|
Peter
|
|
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
The black m84
I mean the led light is on
so it got power
|
 1 user liked this useful post by Mille
|
|
|
|
 Joined: 10/02/2021(UTC) Posts: 3,894 Location: Michigan, Troy
|
What is the dip switch set for? DCC, MM, or MFX
|
|
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
2,3,4
Should be adres 53-56
in manual
|
|
|
|
|
|
Joined: 12/08/2006(UTC)
Posts: 9,277
|
Originally Posted by: Mille  2,3,4
Should be adres 53-56
in manual Dip switch number 10 are to set MM or DCC. I recommended you try DCC protocol and click to search mfx article. Good luck! |
H0
DCC = Digital Command Control
|
1 user liked this useful post by Goofy
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
Still no luck
Dont know what more i can try
|
1 user liked this useful post by Mille
|
|
|
|
Joined: 10/02/2021(UTC) Posts: 3,894 Location: Michigan, Troy
|
If you've already disconnected it and retried, maybe it's defective? Have you checked all. The CS3 settings for correct parameters?
|
|
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
What should be correct settings
in cs3 then?
|
|
|
|
|
|
 Joined: 22/06/2019(UTC) Posts: 27 Location: TIANJIN
|
1. Try another set of address;
2. If have other workable 60842 in CS3, may replace it by new 60842 with same address to see what will happen.
|
1 user liked this useful post by LSQ
|
|
|
|
Joined: 10/02/2021(UTC) Posts: 3,894 Location: Michigan, Troy
|
Yes, and set to DCC, there are more addresses possible, no? Or is it MM? I think the German "trainguy" on YouTube shows how.
|
|
|
|
|
|
Joined: 12/08/2006(UTC)
Posts: 9,277
|
Test by reset CS3.
It is possible that CS3 needs to be clean up.
I did have same similar problem with m83.
After reset CS3 the m83 did start work again. |
H0
DCC = Digital Command Control
|
1 user liked this useful post by Goofy
|
|
|
|
 Joined: 18/11/2007(UTC) Posts: 113
|
There has been a range of Marklin 60842 - M84 Decoders which is not working "correct" because of a failure made under Production. These cant be programmed "manually" or with "mfx" and is not working correct. If the M84 Decoder's Label on the backside of the M84 Decoder has a Serial-number where the last 5 Digits in the Serial-number is inside the Serial-number range shown in the following listing :
41682-41861
40869-41501
40462-40783
38711-40423
37228-38126
 then the M84 Decoder has a Production-failure and can be replaced by your Dealer. Contact your local Marklin Dealer for more Information. |
CS3+ 60216 ( SW:2.5.2 ) / CS2 60215 ( SW:4.3.0 ) / MS2 60653/57 ( SW:4.28 ) / MS1 60652 ( SW:1.8 AP ) / 60883 S88 LINK ( SW:1.1 )
MDT 3 (SW 3.6.0) - HW: ( 60970 / 60971 / 60801 ) & ESU LOKPROGRAMMER ( SW 5.2.12 ) / ESU HW: 53451 / 53900 / 53901
|
1 user liked this useful post by FrankF
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
Sadly my m84 number was not there
I managed to get it work once but i needed to
delete m84 from article list becuse
i choosed an occupied adres
After that cs3 dont find it again
even if i have tried many different
dipswitch settings
Anyone have an idea why??
|
1 user liked this useful post by Mille
|
|
|
|
Joined: 18/11/2007(UTC) Posts: 113
|
Connect the M84 Decoder to the Programming-track and try to read out the M84 - CV Parameters under DCC.
If you can do that set CV 8 to the value "8" and try to reset the M84 Decoder under
DCC and see if this helps you with your problems.
The M84 Decoder only uses MFX-Protokol to add the M84 Decoder to the Article-List , after that the M84 Decoder is used
with the MM or DCC Protokol to control the Switching Articles.
|
CS3+ 60216 ( SW:2.5.2 ) / CS2 60215 ( SW:4.3.0 ) / MS2 60653/57 ( SW:4.28 ) / MS1 60652 ( SW:1.8 AP ) / 60883 S88 LINK ( SW:1.1 )
MDT 3 (SW 3.6.0) - HW: ( 60970 / 60971 / 60801 ) & ESU LOKPROGRAMMER ( SW 5.2.12 ) / ESU HW: 53451 / 53900 / 53901
|
1 user liked this useful post by FrankF
|
|
|
|
Joined: 02/02/2023(UTC) Posts: 68 Location: Stockholm
|
Tried it but only things that happen
is that it add a new article called X1
with adres 12
Guess i need go to my Märklin dealer
Thanks for all help
|
1 user liked this useful post by Mille
|
|
|
|
Joined: 12/08/2006(UTC)
Posts: 9,277
|
Originally Posted by: FrankF There has been a range of Marklin 60842 - M84 Decoders which is not working "correct" because of a failure made under Production. These cant be programmed "manually" or with "mfx" and is not working correct. If the M84 Decoder's Label on the backside of the M84 Decoder has a Serial-number where the last 5 Digits in the Serial-number is inside the Serial-number range shown in the following listing :
41682-41861
40869-41501
40462-40783
38711-40423
37228-38126
then the M84 Decoder has a Production-failure and can be replaced by your Dealer. Contact your local Marklin Dealer for more Information. Strange...i have never notice information by Märklin about the digital problems. It should be present but never heard about info by Märklin. |
H0
DCC = Digital Command Control
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
