First of all, which Marklin controller do you have. "Simple one" is not a model number.

And if you read the previous comments you would know that an mfx decoder is read automatically by most of Marklin current controllers though I am not sure if "simple one" is a current controller model. Also, a current Marklin controller will give priority to the mfx protocol for controlling the loco and ignore the others. Once again, do some reading.

is a mfx on the box but the control station dont detect the mfx which is adress also 46 fabric told in manual... its telling mm2 on the control station is why is confusing she works now but not like others if u click a button its not respondig or u cant slow it down ... in any case i tried to look in the dtabase but is not there . i ahve 2 otehrs models they got fine installed from database..

i do read rhfil but this loco is acting very weird... on the box mister marklinist5999 which replied to me also is telling mfx and not ms2

Christian,

from the behaviour described, it sounds like an old Maerklin analog locomotive being run on a digital layout. The analog models would not respond to controls and would take off at top speed and the only way to stop them was to press the stop button. Some of the early models (1990s) had lights which only functioned via the decoder (function on/off).

Can you open the locomotive and post a photo of the chassis with the PC board? It would help us identify the nature of the model.
A new 37467 would have a mfx decoder similar to the 37460 or 37464.
Can you also post a photo of your controller or it's box as identifying that would help us better evaluate the issue.

Take a track section made up of 2-3 straight sections and connect to your Mobile Station.
Plug Track box into AC (wall)
Press "Stop"
Place locomotive on track
Press "Stop" again
Allow MS to scan for locomotive (Should check mfx, dcc and then MM) (OEM order)

If locomotive simply starts moving, then it is either analog or the decoder is stuck in analog mode.

Regards

Mike C

Hello Mike

yes then u might be right can be analog or old system.. but when i open it is with electronic... i bought it a good 4 years ago.... is brand new also yes when i put it on track i undo stop even i dont add it she goes but just before this message she worked but dont respond properly ok i will take some pictures

in a store she seems to ahve worked but here no way lol was on a bigger marklin station in store...

let me go take pictures

A few more questions to gain more information:

1) Do you have an analog (classic) transformer (66471 or earlier)? to test the model in analog? If yes, connect a few track sections and place the locomotive on the track and run it for 5-10 seconds
Put the locomotive back on the digital layout (alone) and let the controller detect it.

2) If no, do you have a 9V battery and can you connect one wire to the slider and the other to one of the wheels
Let the battery power the locomotive for 5-10 seconds and then remove wires from locomotive

Place locomotive back on track and allow the controller to detect it again.

As you just bought the controller, perhaps your dealer could help you. Can you bring the locomotive and your controller to the shop?
The closest Maerklin dealer (specialist) is probably Anton Furger in Visp
Sion has "Au modelisme" and "Hobby Centre".

Please post the photos requested so that I can better address your particular situation rather than generalities.

Regards

Mike C

Looking at the photos, the details are pretty similar to the 37462 that I have here. My decoder has a green PC board, but the details are the same.
Based on that information, my assessment is that your model is fully OEM and corresponds to what I would expect from a factory model.

The 29000 Set contained a 60657 controller (Mobile Station 2+).

I am going to ask you to check your MS2 library. Click "Shift" and then scroll using the dial.
See if you have a registry for MM46 or 460 105-0 SBB. If yes, select that one and then click on Shift and then "Wrench" and then scroll down to "Remove Loco"

Then allow the MS2 to detect the locomotive again.

Regards

Mike C

oh yes i have the rb103 and another re 460 jubilee digital both got detected by database i found them with the box number but i will fast eat and look what u said on the control to find this in the locomotive database correct? and hwat means wrench in engish?

i let u know later i will do this then u ask me if i understand good to redetect it automatically correct

dear mike i looked but i find no infos on the search u tol dme to find in the database library of locomotives....

i ahve the 29000 set has mfx mm2 and dcc search just for info


the 29000 controle station i bought from the store maybe is not fully update... by the way i saw in google that it has 1000 of htem in the list but i see only a 90 or 100 max 200... maybe is why?

The 29000 should be updated to include the models you have. When I got my 29000, it was to supplement/replace the older gray MS2 that I had.
I was not able to update the original one, as I don't have a Central Station and there is no local dealer who could assist.

I opted for the newer one to be able to access up to 32 functions for most models.

@Kristaki Wrench is the red tool symbol next to the white locomotive on the bottom right button

Regards

Mike C