Searching for instructions

Welcome Guest! To enable all features please Login or Register.

Notification

Error

Searching for instructions

Options

View

Previous Topic Next Topic

dntower85		#1 Posted : 06 November 2006 02:05:55(UTC) Retweet
Joined: 08/01/2006(UTC) Posts: 2,218 Location: Shady Shores, TX - USA		I just picked up an old delta 6603 decoder (but new in box) yesterday at a show. It had everything including noise chokes except for the instructions. I have searchd the net and this site all over and I still have not found instalations instructions. There are a few dead links out there that most likly had the info need but that the way the inter net goes. The most I have found is the conversion to be used with a DC motor. and how to get rid of flickering lites and dip switch setings. I have an exta hamo magnet but I don't know if I need to use it. any info would help
		DT Now powered by ECoS II unit#2, RocRail era - some time in the future when the space time continuum is disrupted and ICE 3 Trains run on the same rails as the Adler and BR18's.


User Profile View All Posts by User View Thanks


	Wish to join the discussion?! Login to your marklin-users.net community \| Forum account or Register a new forum account. Or Connect via Facebook

intruder		#2 Posted : 06 November 2006 21:38:00(UTC) Retweet
Joined: 16/08/2006(UTC) Posts: 5,382 Location: Akershus, Norway		Hello dntower85 This is how the 6603 DELTA decoder is connected: Red wire = pick-up shoe Brown wire = ground in locomotive chassis Green wire = motor magnetic coil forward direction Blue wire = motor magnetic coil reverse direction Black wire = motor cover, metal brush, via noise reducer Gray wire = front lamp Yellow wire = rear lamp Your extra Hamo magnet is not required for the 6603. If you want to get rid of the flickering light you have to make yourself an extra wire form the cathode end of one of the rectifier diodes on the printed circuit board and insulate the bulb sockets form the loco chassis. Connect your new wire (actually +) to one end of the bulb, the gray or yellow to the other end. You better then use 22 Volt bulbs. I normally use 28 Volt bulb to reduce the intencity i bit.
		Best regards Svein, Norway grumpy old sod
		WWW

User Profile View All Posts by User View Thanks

intruder		#3 Posted : 06 November 2006 22:30:48(UTC) Retweet
Joined: 16/08/2006(UTC) Posts: 5,382 Location: Akershus, Norway		Hello again. Some additional information (which I forgot) If you connect the new wire for flicker free light, please put in a 2,7 volt Zenerdiode in series with your wire. Connect it "the wrong way", the cathode should point towards the PCB. You can also connect this wire/Zenerdiode to the black motor wire, as this also comes from the "plus side" of the rectifier diodes. The Zenerdiode is required to keep the decoder memory (anti Alzheimer) at red light stop, as long as a 1,5 Kohm resitor is installed parallell to the signal output. Please see the parts on the table, which is the removed 6603 and motor during converting to the 60923 kit with a 60760 decoder. I'm sorry that it is out of focus.
		Best regards Svein, Norway grumpy old sod
		WWW

User Profile View All Posts by User View Thanks

dntower85		#4 Posted : 07 November 2006 04:15:11(UTC) Retweet
Joined: 08/01/2006(UTC) Posts: 2,218 Location: Shady Shores, TX - USA		Svein, thanks very much :)
		DT Now powered by ECoS II unit#2, RocRail era - some time in the future when the space time continuum is disrupted and ICE 3 Trains run on the same rails as the Adler and BR18's.


User Profile View All Posts by User View Thanks

Users browsing this topic
Guest

Forum Jump

You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.