marklin-users.net community | Forum

 
Welcome to the forum   
Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error
Testing Marklin Turnout Decoders/Motors
Share
Options
View
Go to last post in this topic Go to first unread post in this topic
Previous Topic Next Topic
Offline Alex H  
#1 Posted : 31 October 2025 18:28:13(UTC)
Retweet
Alex H

United Kingdom   
Joined: 25/03/2017(UTC)
Posts: 135
Location: England, Devon
Hi, I am building a new layout and am having issues with some turnouts not working. I am using Marklin C track and the turnouts have motors and decoders built int the track.

I am using the decoders 74462 in the turnouts but for some reason I have about five turnouts that are not working. In one turnout, I replaced both the turnout motor and decoder but it will still not work.

I was wondering if there is any easy way to test the decoder and the turnout motor before installing into the track so that I can eliminate them.

I know I have power on the turnouts - 17.2v and when I put a known working turnout in the same position it works. I have tried altering the DCC ID of the non working turnout but still no luck, so I am running out of options.

Many thanks
Back to top

Wish to join the discussion?! Login to your marklin-users.net community | Forum accountor Register a new forum account. Or Connect via Facebook  
Back to top  
Offline osoraku  
#2 Posted : 31 October 2025 18:49:59(UTC)
Retweet
osoraku

Portugal   
Joined: 22/01/2025(UTC)
Posts: 75
Location: Setubal, Palmela
Dear Alex -

Two suggestions:
1) test function on a programming track;
2) set CV8=8 to reset the decoder (necessary even if you’ve removed power from the track, strangely enough).

Osoraku
Back to top
Offline Alex H  
#3 Posted : 31 October 2025 19:13:52(UTC)
Retweet
Alex H

United Kingdom   
Joined: 25/03/2017(UTC)
Posts: 135
Location: England, Devon
Originally Posted by: osoraku Go to Quoted Post
Dear Alex -

Two suggestions:
1) test function on a programming track;
2) set CV8=8 to reset the decoder (necessary even if you’ve removed power from the track, strangely enough).

Osoraku


Thanks Osoraku - good suggestions which I hadn't thought of. I'll do that in the morning.
Back to top
Offline Goofy  
#4 Posted : 31 October 2025 19:25:20(UTC)
Retweet
Goofy


Joined: 12/08/2006(UTC)
Posts: 9,331
What protocol do you use in the digital system?
If you did reset decoder CV 8 by write value 8, be sure next time to use DIP switches instead.
Pos 10 at DIP switch are to set DCC or MM.
H0
DCC = Digital Command Control
Back to top
Offline Alex H  
#5 Posted : 31 October 2025 19:28:04(UTC)
Retweet
Alex H

United Kingdom   
Joined: 25/03/2017(UTC)
Posts: 135
Location: England, Devon
Originally Posted by: Goofy Go to Quoted Post
What protocol do you use in the digital system?
If you did reset decoder CV 8 by write value 8, be sure next time to use DIP switches instead.
Pos 10 at DIP switch are to set DCC or MM.



Using DCC and yes each turnout decoder has DIP switch 10 set to on. I use the DIP switch to set the DCC ID.
Back to top
Offline rhfil  
#6 Posted : 31 October 2025 20:04:58(UTC)
Retweet
rhfil

United States   
Joined: 05/09/2014(UTC)
Posts: 769
Location: NEW HAMPSHIRE, Somersworth
What controller are you using to operate the switches? Dip switches are not always reliable. Nor motors. I would set all the problem switches to an easy number like 1, connect them all together and then operate them. If they all operate I would then reset the switches to separate numbers and retry them. The ones that did not operate I would check to see what the issue was. It is possible with a transformer or voltage generator to operate a switch motor separately.
Back to top
Offline Alex H  
#7 Posted : 31 October 2025 20:08:33(UTC)
Retweet
Alex H

United Kingdom   
Joined: 25/03/2017(UTC)
Posts: 135
Location: England, Devon
Originally Posted by: rhfil Go to Quoted Post
What controller are you using to operate the switches? Dip switches are not always reliable. Nor motors. I would set all the problem switches to an easy number like 1, connect them all together and then operate them. If they all operate I would then reset the switches to separate numbers and retry them. The ones that did not operate I would check to see what the issue was. It is possible with a transformer or voltage generator to operate a switch motor separately.


Hi. Thanks for the post. I am using a YD7010 as my controller through iTrain (5.17).
Back to top
Offline rhfil  
#8 Posted : 31 October 2025 22:33:24(UTC)
Retweet
rhfil

United States   
Joined: 05/09/2014(UTC)
Posts: 769
Location: NEW HAMPSHIRE, Somersworth
Not familiar with either. But the switch is no more complicated than a solenoid so just hitting the contacts with a pulse will operate it. The 74462 have mfx decoders which can allow the controller to set the address. I prefer not to allow that. Not sure how your controller handles that. Just to be safe I always throw the dip switches in both directions and then relocate them to zero before setting them. According to the instructions the 10th dip switch determines whether the decoder uses fx/mm or dcc protocol with on being dcc. I might want to confirm which position they are in.
Back to top
Offline David Dewar  
#9 Posted : 31 October 2025 23:42:20(UTC)
Retweet
David Dewar

Scotland   
Joined: 01/02/2004(UTC)
Posts: 7,509
Location: Scotland
Being mfx the decoder will register when the turnout is placed on the layout. I use a CS3 so possible the problem is with your set up and somebody with similar may be able to help.
Take care I like Marklin and will defend the worlds greatest model rail manufacturer.
Back to top
Users browsing this topic
Guest
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

| Powered by YAF.NET | YAF.NET © 2003-2025, Yet Another Forum.NET
This page was generated in 0.329 seconds.