Welcome to the forum   
Welcome Guest! To enable all features please Login or Register.

Notification

Icon
Error

Share
Options
View
Go to last post in this topic Go to first unread post in this topic
Offline Bill L  
#1 Posted : 23 December 2022 00:25:27(UTC)
Bill L

United States   
Joined: 08/12/2021(UTC)
Posts: 107
Location: California, Sonoma County
UPcutDSC02863.JPGI hope I posted this in the right section of this Forum. I would like to cut 2 Union Pacific ALCO PA bodies to combine to make a Marklin B unit. I bought the TRIX HO SCALE 22805 UNION PACIFIC ALCO PA AA DIESEL LOCOMOTIVE #600/601 on Ebay at a very decent low price (and I mean they were non-working and INEXPENSIVE). The TRIX and Marklin bodies are the same. The fronts were badly banged up, but the rear ends are fine, so this idea came up.

What is the best saw and blade recommended to use to make the cleanest cut of a zinc body. Would like suggestions from our kitbashing group with all your experience.

Marklin never ever made the B unit and I do not know why.

Thanking you all in advance.

Edited by user 08 July 2024 20:29:46(UTC)  | Reason: To clarify

thanks 1 user liked this useful post by Bill L
Offline kiwiAlan  
#2 Posted : 23 December 2022 00:30:46(UTC)
kiwiAlan

United Kingdom   
Joined: 23/07/2014(UTC)
Posts: 8,187
Location: ENGLAND, Didcot
I would have thought using a bandsaw with a very fine tooth blade would be the way to go. Leave the desired part just a tiny amount oversize then polish off any tooth marks with a fine glass paper.

However I haven't tried this sort of kitbashing, so I am sure someone will come up with a better suggestion.
thanks 1 user liked this useful post by kiwiAlan
Offline Toosmall  
#3 Posted : 23 December 2022 12:35:24(UTC)
Toosmall

Australia   
Joined: 26/07/2021(UTC)
Posts: 635
Location: Sydney
I cut two Z gauge locos in half with a jewellers saw. No issues with cutting.

Wanted to create a twin engine loco out of interest. Have offset the motors 60° filing the ends of the shafts 50% to overlap at the correct rotational angle, and held together with a spare gear, to effectively form a 6 pole motor. It works really well and very smooth.

I used a couple of pins (old drill bits) to join the two halves together.

DSC_1772~2.JPG
thanks 2 users liked this useful post by Toosmall
Offline EMD_GP7  
#4 Posted : 23 December 2022 15:42:13(UTC)
EMD_GP7


Joined: 23/11/2010(UTC)
Posts: 192
Location: U.K. Midlands
Originally Posted by: Bill L Go to Quoted Post
I hope I posted this in the right section of this Forum. I would like to cut 2 Union Pacific ALCO PA bodies to combine to make a Marklin B unit. I bought the TRIX HO SCALE 22805 UNION PACIFIC ALCO PA AA DIESEL LOCOMOTIVE #600/601 on Ebay at a very decent low price (and I mean they were non-working and INEXPENSIVE). The TRIX and Marklin bodies are the same. The fronts were badly banged up, but the rear ends are fine, so this idea came up.

What is the best saw and blade recommended to use to make the cleanest cut of a zinc body. Would like suggestions from our kitbashing group with all your experience.

Marklin never ever made the B unit and I do not know why.

Thanking you all in advance.


Hi. One problem of using 2 A-unit rears is that the B-unit is not symmetrical !
This is because it only has one engine plus radiator unlike the EMD "E" units which have two and are more or less symmetrical.
I built a trix Union Pacific ABA unit some years ago using a Proto 2000 or Athearn B-unit with the wires between the A-units extended but I sold it.
Below is a photo of a Marklin A-unit plus B-units from Proto 2000 ( Centre) and Athearn ( bottom) which may help you with your project.
I would suggest using a Razor saw to cut the bodies if you have no access to a bandsaw as suggested above.

PA_PB.JPG

The radiator air intakes are clearly seen on the right side of each unit.

Good luck with your project, Colin.

thanks 2 users liked this useful post by EMD_GP7
Offline Alsterstreek  
#5 Posted : 23 December 2022 16:35:51(UTC)
Alsterstreek

Germany   
Joined: 16/11/2011(UTC)
Posts: 5,741
Location: Hybrid Home
Posts #100/101/102 in this thread might of interest in this context:

https://www.marklin-user...Marklin-ALCO-PA-1-models
Offline Bill L  
#6 Posted : 28 December 2022 03:37:59(UTC)
Bill L

United States   
Joined: 08/12/2021(UTC)
Posts: 107
Location: California, Sonoma County
Thank you for your input kiwiAlan, Toosmall, EMD_GP7, and Alsterstreek.
I will be making straight cuts, so I will look into a jeweller saw blade with a larger width and small blade thickness, that will give me a straight cut, I do not need to make any curve cuts here. Also, a higher number of teeth per cm will help.
A razor saw might work, I will look into that as well.
Thanks again.
Offline Bill L  
#7 Posted : 08 July 2024 20:40:13(UTC)
Bill L

United States   
Joined: 08/12/2021(UTC)
Posts: 107
Location: California, Sonoma County
Reposting.
Two A units were cut up to make the B unit.

UPcutDSC02863.JPG
thanks 4 users liked this useful post by Bill L
Users browsing this topic
OceanSpiders 2.0
Forum Jump  
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.

| Powered by YAF.NET | YAF.NET © 2003-2024, Yet Another Forum.NET
This page was generated in 0.866 seconds.