 Joined: 14/12/2002(UTC) Posts: 800 Location: Newcastle NSW Australia
|
I picked up a HAMO 3829 [ BR 191 ] a few years ago on EPay & have not given it a run till this morning . It had been converted to 3 rail & supposably digital . When placed on the programme track for the CS1 upgraded it was not a goer . Worked out how to remove the top body , 5 screws in hidden places & then removed the brushes to see what was stuck , still no go & then took off the brush plate which is a major operation having to remove the coupling rods & external transfer case to get enough room to get the brush plate off to access the anker , wheels now turned ok , counted the teeth on the anker ,7, & looking at the exploded view on the web there is no teeth shown, Part #245480 . I let off the 2 mounting screws a fraction & the motor will buzz but not rotate, but with no anker fitted wheels turn with no excessive friction I am concerned that a wrong anker has been fitted prior to me buying this engine . Can anyone advise which anker part # should be fitted & also advise what sort of Decoder ? is fitted to the engine please . See picture below . Cheers Tom in Oz Tom Jessop attached the following image(s):
|
|
|
|
|
|
Joined: 12/07/2011(UTC) Posts: 1,068 Location: In a building site in Yeppoon
|
5 pin anchor with 8 teeth: 1 Piece 386820
If it has the original Decoder: 960820 (it is DCC)
As to the decoder, can't say I recognise it, could be a optical illusion but a couple of the diodes look burnt. Could you do a photo of the other side Tom. |
Sad when its cheaper to buy a new 29640 starter set from Germany than a CS2 on its own in Oz, welcome to the joys of Marklin down under . |
|
|
|
|
|
Joined: 14/12/2002(UTC) Posts: 800 Location: Newcastle NSW Australia
|
Other side of decoder. Cheers Tom in Oz. Well that's not a good shot, try this one . Just a bit better, taken with a cheap Fuji camera with poor zoom /macro Tom Jessop attached the following image(s):
|
|
|
|
|
|
 Joined: 23/07/2014(UTC) Posts: 8,481 Location: ENGLAND, Didcot
|
Originally Posted by: Shamu 
As to the decoder, can't say I recognise it, could be a optical illusion but a couple of the diodes look burnt. Could you do a photo of the other side Tom.
I don't think anything is burnt, I think it is just paint on the body of the component. As there are no dip switches this is very likely to be marklins early DCC decoder (IIRC 6081?).
|
 1 user liked this useful post by kiwiAlan
|
|
|
|
Joined: 21/10/2004(UTC) Posts: 31,692 Location: United Kingdom
|
I have the same one from Hamo digital 2-rail loco. I think it is from 6082 c82 decoder for 2-rail digital.
It work with Marklin 6027 2-rail Central unit= only, Changing coding with Marklin 6032 programmes. |
Large Marklinist 3- Rails Layout with CS2/MS2/Boosters/C-track/favorites Electric class E03/BR103, E18/E118, E94, Crocodiles/Steam BR01, BR03, BR05, BR23, BR44, BR50, Big Boy. |
1 user liked this useful post by steventrain
|
|
|
|
 Joined: 31/12/2015(UTC) Posts: 1 Location: California
|
Hi. Do any of you have the manual or can provide the link for the 3829?
I got one too, second hand, but its missing its paperwork
Thanks in advance !
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.
